Pi PicoW and WiFi0

 Got PicoW to send HTML Hello World web page to chrome browser via internet. The program from Creating a Wireless Network With Raspberry Pi Pico W Part 1 - Instructables below created an access point in a PicoW ie. put it into AP mode.

Pics: Code in black bit lower








import network
import time
import socket


def web_page():
  html = """<html><head><meta name="viewport" content="width=device-width, initial-scale=1"></head>
            <body><h1>Hello World</h1></body></html>
         """
  return html

# if you do not see the network you may have to power cycle
# unplug your pico w for 10 seconds and plug it in again
def ap_mode(ssid, password):
    """
        Description: This is a function to activate AP mode

        Parameters:

        ssid[str]: The name of your internet connection
        password[str]: Password for your internet connection

        Returns: Nada
    """
    # Just making our internet connection
    ap = network.WLAN(network.AP_IF)
    ap.config(essid=ssid, password=password)
    ap.active(True)

    while ap.active() == False:
        pass
    print('AP Mode Is Active, You can Now Connect')
    print('IP Address To Connect to:: ' + ap.ifconfig()[0])

    s = socket.socket(socket.AF_INET, socket.SOCK_STREAM)   #creating socket object
    s.bind(('', 80))
    s.listen(5)

    while True:
      conn, addr = s.accept()
      print('Got a connection from %s' % str(addr))
      request = conn.recv(1024)
      print('Content = %s' % str(request))
      response = web_page()
      conn.send(response)
      conn.close()

ap_mode('NAME',
        'PASSWORD')




Comments

Post a Comment

Popular posts from this blog

Reading LittleFS file into buffer for sending

 Reading LittleFS file into buffer for sending to another ESP32 via ESP Now. Created dummy file 1321 bytes long with "sensor" information in the form like this:     uint8_t sensorData1[] = "[ 00 12:05:12:06:01 22 33 44 \n"; Red stuff above is timestamp to later get in real time from DS3231.  Blue stuff is dummy sensor information, two ascii chars representing 00 to 99. Black stuff is just formatting chars and spaces. The following program reads in about 43 lines of sensor information as above and puts it into LittleFS file called sensorReadings.txt. This file then gets cut up into 200 byte chunks (via sendBuf[200] ) and gets sent to dummy sender file called sendNowBuf(). No actual sending takes place, so next sub-project is to send the 200 byte chunks one by one via ESPNow to second ESP32. //41 From Arduino Examples/mnt/c/Users/Dell/Documents/Arduino/Working202411/LITTLEFS_test2/LITTLEFS_test2.ino #include <Arduino.h> #include "FS.h" #include <Li...
Read more

ESP32 buttons and bouncing

 ESP32 buttons and bouncing Rigged up button to GPIO 21 to explore, button presses, debouncing and interrupts. Following worked. /*  * This ESP32 code is created by esp32io.com Worked 7/11/24  *  * This ESP32 code is released in the public domain  *  * For more detail (instruction and wiring diagram), visit https://esp32io.com/tutorials/esp32-button-debounce  */ #include <ezButton.h> #define DEBOUNCE_TIME 50 // the debounce time in millisecond, increase this time if it still chatters ezButton button ( 21 ) ; // create ezButton object that attach to pin GPIO21 void setup () {   Serial . begin ( 9600 ) ;   button . setDebounceTime ( DEBOUNCE_TIME ) ; // set debounce time to 50 milliseconds } void loop () {   button . loop () ; // MUST call the loop() function first   if ( button . isPressed ())     Serial . println ( "The button is pressed" ) ;   if ( button . isReleased ())     Serial . pri...
Read more